Force-Gauge.net - Quality force testing and torque testing products and materials testing equipment
Contact UsYour AccountYour CartHome
Force Gauges
Torque Testing
Test Stands
Grips & Accessories
Software
 
Chatillon
Dillon-Quantrol
Hoto Instruments
Imada
Lafayette Instruments
Mark-10
 
Show Cart
Contact Us
Home
 
 
 
 
 
 
 
Mark-10 BG Digital Force Gauges
Mark-10 >> Force Gauges >> Digital Force Gauges

Mark 10 BG Digital Force Gauges

Compare Mark-10 Force Gauges
Click here

Mark 10 BG Digital Force Gauges
Shipping Weight: 10 lbs
currently in stock
estimate shipping cost
FREE UPS Ground Shipping with ANY Mark-10 Purchase!
(48 continental US states only)

Model:   

Cable, BG/CG/EG/BGI to Mitutoyo SPC (09-1047), Add $71
Cable, BG/CG/EG/BGI to RS-232, 25-pin (09-1048), Add $71
Cable, BG/CG/EG/BGI to RS-232, 9-pin (09-1048A), Add $71
Cable, set point, BG/BGI/CG to test stand (09-1090), Add $137
Hi / Lo limits indicator for BG/BGI/CG (11-1022), Add $85
Overload protection module, BG/CG/EG/BGI to test stand (11-1042), Add $185

FREE UPS Ground Shipping with any Mark-10 purchase!The Mark 10 BG Digital Force Gauge is an advanced force measurement solution with sophisticated measurement capabilities, data outputs, computer control capabilities, and a long list of features and configurable settings. The BG can stop motorized test stand travel at user-selectable set points, and can also prevent force overload (when used with the ESM motorized test stand). Go / no go testing can also be accomplished with an optional plug-in hi / lo limits indicator.

Features:

  • Compatible with all Mark 10 test stands and grips
  • RS-232, Mitutoyo and analog outputs
  • GCL-Gauge Control Language for full computer control
  • Automatic timed output on RS-232
  • Dual set points with outputs
  • Averaging mode for average readings over time
  • External trigger for contact or switch testing and data capture
  • General purpose I/O for external device control
  • Programmable analog and digital filters
  • Selectable units of measurement
  • Programmable default configuration
  • Peak memory for tensile and compressive forces
  • Push-button calibration
  • Battery or AC operation
  • Programmable automatic shutoff
  • Reversible aluminum housing for handheld use or test stand mounting (see below)
  • Same housing size for all capacities

Specifications

  • Accuracy: ± 0.2% of full scale ±1 digit
  • Sampling rate: 65 readings/sec
  • Display rate: 25-10/sec, 65/sec in peak mode
  • Display: 4-1/2 digit, 0.3 inch (7.6 mm) high LCD
  • Indicators for low battery , units and mode of operation
  • Power: AC or rechargeable battery with IPM, a 3-step Intelligent Power Management system that warns the user via "LO BAT" indicator and then will shut off the gauge
  • RS-232 - Fully configurable up to 9600 baud. Includes GCL (Gauge Control Language)
  • Mitutoyo output - Serial BCD suitable for all Mitutoyo SPC-compatible devices
  • Analog output - +/-VDC +/-0.25% of full scale at capacity. Positive for compression, negative for tension
  • Set point outputs: 3 open collector lines (utilizing Mitutoyo lines)
  • General purpose I/O: 3 open collector outputs and one input (utilizing Mitutoyo lines)
  • Sensor detection: 0.010 (0.25 mm) maximum deflection at full load
  • Safe overload: 150% of capacity - display shows "==" at 110% and above
  • Battery life: 8-10 hours per charge
  • Weight - Gauge only: 0.9 lbs (0.4 kg)
  • Environmental requirements: 40°F - 100°F [5°C - 45°C], <96% humidity (non-condensating)
  • Warranty: 3 years

The Mark 10 BG digital force gauge is compatible with all Mark-10 force measurement test stands. It is shown here in a tensile testing application, mounted to an ESM motorized test stand with optional items: digital travel display, limit switches, and wedge grips.

Mark 10 BG Digital Force Gauges Mark-10 BG force gauges are supplied in a cushioned carrying case with AC adapter, rechargeable battery, chisel, cone, v-groove, hook, flat, extension rod, user's manual, and NIST-traceable certificate of calibration

Reversible Housing - A Mark-10 Exclusive

All Mark-10 force gauges have reversible housings that allow the user to use the gauge with the load cell shaft pointing up or down, without the inconvenience of upside-down buttons and display. The housing for Mark-10 BG and Series EG gauges is reversible by separating the two halves and reassembling them with just one connector - an extra bit of engineering that will make your testing setups quicker and more efficient.

Mark 10 BG Digital Force Gauges

Optional Equipment:

  • A wide range of test stands and gripping fixtures
  • Hi / lo limits indicator - Set limit conditions for a test - the indicator will display red lights for high and low limits, and a green light to indicate passing.
  • Overload protection module - Protects the force gauge against overloads during motorized tests, adjustable from 20 - 110% of gauge's full capacity. For use with Mark-10 motorized test stands.
  • Set point cable - Stops test stand travel at programmable high and low set points for tension and compression forces. For use with Mark-10 motorized test stands.
  • Output cable - Send test data to a PC, statistical printer, or other data collector for further analysis.

 

Model Capacity x resolution Price
BG012 0.12 x 0.00005 lb, 50 x 0.02 gF, 0.5 x 0.0002 N, 110V $1087
BG025 0.25 x 0.0001 lb, 100 x 0.05 gF, 1 x 0.0005 N, 110V $1087
BG05 0.5 x 0.0002 lb, 250 x 0.1 gF, 2.5 x 0.001 N, 110V $1087
BG2 2 x 0.001 lb, 1 x 0.0005 kgF, 10 x 0.005 N, 110V $945
BG5 5 x 0.002 lb, 2.5 x 0.001 kgF, 25 x 0.01 N, 110V $945
BG10 10 x 0.005 lb, 5 x 0.002 kgF, 50 x 0.02 N, 110V $945
BG20 20 x 0.01 lb, 10 x 0.005 kgF, 100 x 0.05 N, 110V $945
BG50 50 x 0.02 lb, 25 x 0.01 kgF, 250 x 0.1 N, 110V $945
BG100 100 x 0.05 lb, 50 x 0.02 kgF, 500 x 0.2 N, 110V $945
BG200 200 x 0.1 lb, 100 x 0.05 kgF, 1000 x 0.5 N, 110V $1087
BG500 500 x 0.2 lb, 250 x 0.1 kgF, 2500 x 1 N, 110V $1087
Optional Equipment
09-1047 Cable, BG/CG/EG/BGI to Mitutoyo SPC $71
09-1048 Cable, BG/CG/EG/BGI to RS-232, 25-pin $71
09-1048A Cable, BG/CG/EG/BGI to RS-232, 9-pin $71
09-1090 Cable, set point, BG/BGI/CG to test stand $137
11-1022 Hi / Lo limits indicator for BG/BGI/CG $85
11-1042 Overload protection module, BG/CG/EG/BGI to test stand $185

 

Dimensions:

Model ØA B C Thread
BG012-BG-200
0.2 (5.8)
0.19 (4.8
0.35 (8.9)
#10-32
BG500
0.312 (7.9)
0.44 (11.2)
0.60 (15.2)
5/16-18

 

Mark 10 BG Digital Force Gauges

Top


Home | Site Map | Shopping Cart | Store Policies | Your Account

Force-Gauge.net - an Itin Scale Company
4802 Glenwood Rd.
Brooklyn, NY  11234
Phone: (718) 336-5900
For orders phone 800-832-0055
FAX: (718) 627-1313


©2002-2016 Force-Gauge.net, All rights reserved
Email sales@force-gauge.net with comments or questions about this site